1675

Item 1675

DESIGN: AeroVantage ~ PropRotor - Hub - .1x2 .- Layout w/ Swashplate w/ Gears

Notes:

This is for the 1x2 PropRotor. Therefore it must provide both collective and cyclic pitch control.

Drawing:

Options for Consideration:

Use 6 instead of 3 linear actuators for redundancy. Two would operate at each end of a teetering bar to move a pitch rod. The failure of 1 would limit the total movement to 50% (25% on each side of the flailed actuators extension). Would like; same Force, and same stroke, but 50% of the speed.

See 1687.html for an optional component to/in the above.

Description of Operation:

Put hydraulic valves at Proprotor and only 2 hydraulic lines to 3 pitch and 1 wrist servos? Then take electric wiring to individual hydraulic valves

Advantages Over AeroVantage ~ Proprotor - Hub - 1x2 - Layout w/ Independent Blade Control:

Having the linear actuator move the swashplate will result in their moving approximately 1/100 the number of times that they will move on the Independent Blade Control. This rough conclusion is based on a rotor speed of 1,500 rpm and the pilot moving the cyclic stick once per four seconds.

There is no need for up to 30 slip-rings between the rotor hub and the PropRotor housing. One multi-wire cable will come out the side of the PropRotor housing.

Notes:

Ref;

The currently electric linear actuator used on the drawing is the ZABER ~ NA14B60. The slightly larger ZABER ~ NA23C60 will also fit in and it may be safer (more reliable) to use the larger one.

Electrical Linear Actuator:

Zaber http://www.zaber.com/products/product_group.php?group=NA

Linear actuators have a built in magnetic home sensor. This may not be good enough since this can only be set when the PropRotor in its home position, which will probably be at the end stop at minimum pitch. For example, on the ground before takeoff. To control actuator position, simply transmit the unit number of the T-CD controller you want to move, a simple move command and the position desired. After the move, the controller will report its position. Does this take into account any missed steps?

Hydraulic Linear Actuator:

Clippard Minimatic http://www.wainbee.com/suppliers/Clippard/Cylinders/CLI_minimaticCylinder.pdf Starting at page 10

H9C-2D

Have a large spring on the center of the non-turning portion of the swashplate to oppose the hydraulic pressure from the single port. The spring will also move the swashplate to the 'home' position, after the pressure has also been removed from the other 2 cylinders.

It is extremely unlikely that a cylinder could lock-up. The worst might be the loss of pressure in one cylinder (due to ??) and this will be caught by the sensor and computer. A small leak in the line should only result in spilt oil.

Alternative Position for Actuator:

Locate the actuators above the planetary gears.
This has the advantages of;

Having them easily accessible by the removal of the hub-cone.
The wiring or the hydraulic line passes through the planet holder.
The actuator is removed from the 'gearbox' and its oil.

Consider pivoting the mount of the actuators on an axis normal to the radials of the PropRotor. This way they might be used in lieu of a scissors to stop the rotation of non-rotating portion of the swashplate.

Cooling:

DESIGN: AeroVantage ~ Motor / Genset / Engine - Full-size Motor - Cooling

Related Pages:

AeroVantage ~ Power Train - Planetary Reduction; for 1x2

Initially displayed: October 2, 2005 ~ Last Revised: January 26, 2009

The above utility invention is openly and publicly disclosed on the Internet to negate an entity from patenting it, to the exclusion of all others whom may wish to use it. ~ Reference patent law 35 U.S.C. 102 A person shall be entitled to a patent unless - (a) the invention was known ... by others in this country, ..., before the invention thereof by the applicant for patent.